6/27/2023 0 Comments Northwest shortline chopper 2* Parts listed are for O Scale and can be adapted for other scales.Ĭut 8 #268 channel pieces to the fit the width of the. # 90517 I-beam (5/16”) - use with #268 channel to make upright columns. 020”) - use for the web of the plate girder. # ? Sheet (.020") - to make assorted strips and/or webbing Plastruct Styrene: 250”) - to make top & bottom sills on plate girder. # 268 Channel (5/16”) - to make upright columns and ribs on cross girders. # 293 Angle (.100”) - to make the ribs in the plate girder. # CS397 - Corner Brace Evergreen Styrene: # CS002 - Third Rail Chair (IND, BMT, Round) (track) Zap-A-Gap CA+ (super glue) *Parts: Q-Car Company: Scale ruler (for the scale you’re working in) Testors: Single edge razor blades (as replacements for Chopper or instead of X-acto knife) List of Suggested Tools & Glues and Partsįor This Project Tools & Glues: NorthWest Short Line: The photos on this page can be enlarged by clicking on them. The clearance under the el shouldīe between 15 to 20 scale feet, but can be less depending on the situation. Out of the material used and the dimensions figure easier. Simplify this further, shortening the length to 48 scale feet or 12 inches, you can get more The length works out to 50 scale feet or 12-1/2 inches. For instance, in O scale, the depth of the girders should be a When joiningĭissimilar parts, such as styrene to metal, a "super" glue is used.įollowing the drawings and descriptions used in the book mentioned above, one can scale down This liquid will actually melt the pieces together to create a strong joint. The best glue to use to join the styrene pieces is Testors liquid cement (or similar product). Using this tool or any tool, follow the operating instructions and safety precautions Size consistently, making it easy to collect enough parts to build in mass. Shop doesn’t have them in stock, they can usually order just what you want.Ĭutting these strips and shapes to length in quantity is the key to building the structure,Īnd a tool called "The Chopper II",from Northwest Shortline, Styrene was chosen here because it is easily cut and there is anĮxcellent variety of shapes and sizes currently available. "Building The New Rapid Transit System of New York City Circa 1915"įor this project, we will be using styrene plastic strips and structural shapes that areĬommercially available. This design was very standardized and simplified from previous elĬonstruction and is easily adapted, and reduced to O scale - or any scale for that matter.Īn excellent source of information regarding this type of structure is the book, This type of structure can be found on lines including - Astoria, Flushing, West End, Culver,Īnd IRT lines in the Bronx. The structure modeled here is based on the city built "dual contracts" design. Being inspired by the great model structures of Nate Gerstein, Joseph Frank, and Bob Olson, I have set out to build my own! This page shows ways to build NYC style El structure. This is the Four Piece Premium Micro Tweezer Set from Squadron Products.Modeling New York City Elevated Structure The perfect tool to hold your car or locomotive work. The perfect foam holding block for your locomotive work Peco Locomotive Service Cradle for HO,N, OO, HOn3 This is the best stick for general structure and construction needs. So it can be applied to a glass surface or small block.Ī small amount of water can be used on the surface Scratches then follow with the White super fine to The Grey coarse film can be used to rough polishįollowed by the Pink fine film to remove most surface This tool is for marking holes to mount Tortoise switch machines with no guessing.ĥ Sheets of 15 micron grit film (coarse grey)ĥ Sheets of 3 micron grit film (fine pink)ĥ Sheets of. The blades are made of rustproof hardened alloy steel. This set contains 4 flat screwdrivers (sizes 1.4 mm, 2.0 mm, 2.4 mm andĢ.9mm) and 2 phillips (#0 and #1.2) with chrome plated swivel headed handles. Power Supply: 1 * 9V battery (not included) Low battery indication, Ranging mode: manual Measuring AC/DC voltage, DC current, resistance, Continuity Beeper testĭiode and transistor test, Data hold for easy readingĭigital LCD Display with Backlight, Automatic polarity indication Pocket DM Pocket DMM Digital Multimeter A830L This is a Northwest Short Line 69054 Replacement Cutting Mats For Chopper II. Northwest Short Line Chopper II Replacement Pad This is a Northwest Short Line Chopper II.
0 Comments
Leave a Reply. |